Welcome our website!.http://www.louisvu.com/ Log In  |   account

4Pcs 1806 2400KV Brushless Motor + 4Pcs Simonk 12A ESC for DJI F330 ZMR250 H250 Quadcopter

Price:  $80.14

  • Model: RM2126
  • 888 Units in Stock



Add to Cart:




4Pcs High Performance Simonk Firmware 12A Brushless ESC Speed Controller
Description:
Brand: Simonk
Item name: 12A ESC
Continuous current: 12A
BEC: 2A
Burst current: 16A (10 Seconds)
Battery: 2-3S Li-Po / 5-12S Ni-XX
NI-CD/NI-MH: 4-10 cells
Weight: 22g
Size: 32x22x5mm
 
Designed for: 
Multicopter with SimonK Firmware
Suitable SimonK Firmware is BS.HEX (you can upgrade it by yourself using KK Flash Tool)
 
Features:
Extremely low internal resistance.
Super smooth and accurate throttle linearity.
Safety thermal over-load protection.
Auto throttle shut down in signal lose situation.
Supports high RPM motors.
Power arming protection (prevents the motor from accidentally running when switched ON).
New Advanced programming software.

2 Pairs High Quality 1806 2400KV Brushless Motor Plus/CCW Thread

1806 2400KV Micro Size Outrunner Brushless Motor Designed for Multicopter
As of testing, full load of this motor demands between 6A - 8A current. So a >10A ESC is recommended, a 6A ESC might be too low if you need to drive it very hard.This is a great little motor suitable for multirotor helicopters size between 200-330mm.

Description:
Motor Diameter: Approx. 23.6mm
Motor Shaft Diameter: 5mm
Capable of 6-12~ amps of power draw
Includes 1 spinner (5mm diameter) and 4 M2x5 phillips mounting screws
Motor wire length = 40mm

Which ESC is suitable for this motor?
The testing (with 3S Li-Po, 10A ESC and both 5030 2-Blade & 3-Blade Propeller) shows that this motor demands between 7.5 - 8.5A during full load (100% Throttle). So a 10A ESC is preferred to avoid overheat if you plan to drive this motor hard. The temperature of  10A ESC was only a little warm after a continuous full load after 5-6 minutes.
10A G Series SimonK (better option)
10A SS Series SimonK (economy option)
A wholesales customer reported that the motors work beautifully which he used 4S 2200mAh 25C with 12A ESC on 5030 Props. But we have not yet tried so it is not guaranteed but you are welcome to report.

Washer Needed?
Depends on the thickness of the frame which you will install this motor, you might need to use a washer with the screws because they might be too long if your frame is thin. So you need to check this carefully during the installation (to see whether the screw is too close to the motor wire inside. If yes, then you need to use a washer).

The Washer needed is M2 Washer. Beside using washers, you may also consider to use shorter screws eg. 2*5 or 2*4 depends on the thickness of the frame.

The thickness of the frame that this motor was originally designed for is 2.2mm. The screw is about 2*6 (Diameter is about 2mm and the total length is about 5.8mm). So in that case if the thickness of your frame is less than 2.2mm, then you might need to use a Washer, and you need to check carefully during installation whether the screw is too long which touches of the wire inside the motor

Package size: 20 * 15 * 5cm / 8 * 6 * 2 in
Package weight: 158 g / 5.6 oz

Package list:
2 * 1806 2400KV Brushless Motor Plus Thread
2 * 1806 2400KV Brushless Motor CCW Thread
4 * Simonk Firmware 12A Brushless ESC Speed Controller








;;;;;;;;

Choose a ranking for this article, from 1 star (worst) to 5 stars (best):



NOTE : HTML tags are not allowed.
NOTE: Reviews may require prior approval before they will be displayed